Forum Navigation
Post History: GPSWebShop Official
The G-sensor component inside the P-1 Mark II and P-10 Pro can produce a very light clicking sound w …In: Why does the P-1 Mark II or P-10 Pro make a slight sound when shaken?
2 weeks ago
If you send the command but receive no response, please check the following two items:
1. The defau …In: How to restore the factory settings of P-7 Pro?
2 weeks ago
Please refer to the official guidance from Columbus GPS here:
https://cbgps.com/p7/app/gnsstoolkit/ …In: How can P-7 Pro users outside Asia optimize their GNSS constellation settings?
2 weeks ago
1. Download the GNSSToolKit for Windows.
2. Please use the command “PQSETCNST,47” to restor …In: How to restore the factory settings of P-7 Pro?
3 weeks ago
If the EX-1 is not functioning properly, please try the following steps:
Connect the device to …In: How to reset the EX-1 GNSS data logger
1 month ago
You can find the EX-1 firmware file and the update instructions on this page:
https://cbgps.com/ex1 …In: Where can I find the EX-1 firmware file - EX1.bin?
1 month ago
Since 2018, Apple has restricted external GNSS receivers from accessing the iOS Location Service. Th …In: Why does the P-7 Pro have only limited support for iOS and iPadOS?
2 months ago
The reason could be your config.txt file is not recognized by the EX-1 may be due to formatting diff …In: Why can’t my config.txt file be recognized by the EX-1?
7 months ago
Instead of using commands, you can now use the latest version of the NaviViewerAh software to change …In: How to change the update rate of the Navisys GR-M02 GNSS receiver?
8 months ago
I’ve been informed that the Bluetooth GNSS connection issue has been resolved — the latest version 1 …In: Workaround for P-7 Pro Connection Issue with “Bluetooth GNSS” App - v1.0.69
8 months ago
This is primarily due to the satellite acquisition strategy used by the P-7 Pro.
The P-7 Pro is des …In: Why does the P-7 Pro show fewer satellites and constellations compared to other GNSS receivers?
8 months ago
There is a known issue with version 1.0.69 of the “Bluetooth GNSS” app (released on March 22, 2025) …In: Workaround for P-7 Pro Connection Issue with “Bluetooth GNSS” App - v1.0.69
9 months ago
Since 2018, Apple has restricted external GNSS receivers from accessing the iOS Location Service. Th …In: Could you explain why the P-70 Ultra has only limited support for iOS and iPadOS?
9 months ago
When configured in Spy Mode, the P1-M2 can be set to wake up from sleep at intervals ranging from 1 …In: What is the battery runtime of the P1-M2 in Spy Mode?
9 months ago
• IMU Calibration (Device Menu):
This function calibrates the IMU module to maintain accuracy. Ove …In: Could you explain the difference between “IMU Calibration” in the “Device” menu and “IMU Initialization” in “Point Survey”?
10 months ago
This depends on the “Smooth” (Average GPS Count) setting and the IMU:
•If Average GPS Count is set …In: When collecting a data point with "CreateYours" software, the process typically takes a few seconds. Does slight movement of the survey pole affect accuracy?
10 months ago
This issue may be caused by your Android device’s “App battery usage” settings.
Suggested Fix:
Ple …In: Why does the GR-9029 disconnect from my Android BLERTK app after a few minutes?
10 months ago
Swipe down from the top of the P3 screen with your finger to open the quick access menu. You will se …In: How to Take a Screenshot on the P3 Data Collector/Controller?
10 months ago
For a standard survey or stakeout, you can connect the Gintec G50 GNSS receiver to the data controll …In: Why is a WiFi connection required between the G50 and the data controller for Laser Survey or Stakeout?
10 months ago
Yes, we can customize the TOP608BT with an RS-232 interface instead of a USB interface. However, ple …In: Can you customize an RS-232 version of the TOP608BT?
10 months ago
When you connect a Bluetooth GNSS receiver (e.g., TOP608BT or RTU609BT) to Windows, you’ll notice tw …In: Why do two “Serial over Bluetooth” COM ports appear when pairing the Bluetooth GNSS receiver to Windows?
10 months ago
The default baud rate for the USB port of the P-70 Ultra is 230400.
For Bluetooth, it automatically …In: What is the default baud rate for the Columbus P-70 Ultra GNSS receiver?
11 months ago
The Prolific PL2303 is a widely used USB chip in many GPS/GNSS devices on the market, such as the Na …In: How to Install the Prolific PL2303 USB GPS/GNSS Driver for MacOS?
11 months ago
Here are a few key points to keep in mind when using Emlid Studio for PPK processing with the EX-1. …In: Practical Tips to Improve EX-1 PPK Accuracy
12 months ago
As of January 9, 2025, the Bluetooth function on the P-9 Race cannot be disabled by the end user. If …In: Can I Disable Bluetooth on the Columbus P-9 Race?
12 months ago
Please refer to this blog post.
https://community.gpswebshop.com/2022/11/27/how-to-connect-a-gnss-r …In: How do I install the Windows Location Sensor Driver for the Navisys GR-8018U?
12 months ago
The X8-M1 uses a standard 1/4”-20 UNC thread, which is the most common mount thread size for consume …In: What type of mount thread does the X8-M1 use?
1 year ago
GBoxTools is an Android app that isn’t available on the Google Play Store. Instead, you can download …In: How to Install the GBoxTools Android App?
1 year ago
The X8-M1 uses a spiral antenna, with positioning readings referenced from the center of the antenna …In: Which part of the X8-M1 does the positioning reading refer to?
1 year ago
1. Power On the GNSS Receiver
•Connect the Columbus P-9 Race GNSS receiver to a USB charger or powe …In: How to Pair the P-9 Race with Windows 11 via Bluetooth?
1 year ago
Please refer to the official Columbus article below and make sure to follow each step as described.
…In: What should I do if my P-10 Pro fails to boot after a firmware upgrade?
1 year ago
Columbus has published field tests for the EX-1 covering four different scenarios. They provide samp …In: Where can I find sample data recorded by the Columbus EX-1 for download?
1 year ago
Please refer to the Qstarz Official site.
http://racing.qstarz.com/Products/LT-8000S.html
I pasted …In: Side by side comparision: LT-8000S vs LT-8000GT vs LT-6000S
1 year ago
The Navisys Survey Pole Adapter (as shown in the image below) is designed to connect the GR-903, GR- …In: Navisys Survey Pole Adapter Clarification
1 year ago
By default, the EX-1 “Base” mode has MSM4 enabled and MSM7 disabled. This is because MSM4 has a smal …In: Notes for MSM4 vs. MSM7 in the RTCM Configuration of the EX-1
1 year ago
1. RTK Mode - Static Testing
Objective: Evaluate whether the positioning accuracy of the EX …In: EX-1 Field Test
1 year ago
The EX-1 driver is built into Windows 10/11, so there is no need to install any additional drivers. …In: Where to Download the Windows 10/11 Driver for EX-1 RTK GNSS Data Logger Receivers?
1 year ago
Step 1: Install and Launch u-center 2
1.Download and install the latest version of u-center 2 from …In: How to change the Update Rate of a Navisys GR-U01 (u-blox M10) GNSS Receiver?
1 year ago
The default update rate of the GR-M02 is 1 Hz, but you can change this setting to a different value, …In: How to change the update rate of the Navisys GR-M02 GNSS receiver?
1 year ago
The blog post below provides a more detailed explanation.
Why can’t you rely on some GPS/GNSS apps’ …In: Why is the P-7 Pro experiencing reduced accuracy when tested with certain apps?
1 year ago
https://community.geoastra.com/tech-support/In: GeoAstra Products' Support Forums - https://community.geoastra.com/tech-support/
1 year ago
1 year ago
In my testing, all power banks work initially. However, when the P-10 Pro is fully charged, the powe …In: Which power bank do you recommend for the P-10 Pro to extend its runtime?
2 years ago
The BLERTK app has recently added a new feature. In addition to using "Survey-in" to acqui …In: How the GR-9028 acquired Base Station location?
2 years ago
please connect your GR-9028 to the BLERTK app and navigate to the "Base Source" menu. You …In: How to achieve the highest accuracy
2 years ago
You could download the TimeAlbum Pro V3.0
https://cbgps.com/download/tap/3.0/TimeAlbumProMac.app.zi …In: TimeAlbum Pro V2.32 can't get maps on Apple Mac
2 years ago
The P-7 Pro has the following accuracy specifications: horizontal direction 0.5m CEP(50%) and 1.5m C …In: Geotagging Photos
2 years ago
Hi Garrett,
Yes, you can use the P-7 Pro with your Android phone for improved accuracy in photo geo …In: Geotagging Photos
2 years ago